Modulating Automation Kit for Valves with IO-Link | PROFINET EtherNet/IP EtherCAT | Proportional Control
Pickup availability could not be loaded
Modulating Automation Kit for Valves with IO-Link — Continuous Proportional Control, Predictive Diagnostics, Compatible with PROFINET EtherNet/IP EtherCAT
Cematic's IO-Link modulating automation kit for valves is the solution for continuous proportional control of ball and butterfly valves in industrial facilities with PROFINET, EtherNet/IP, or EtherCAT networks.
Unlike On-Off kits that only operate in fully open or fully closed positions, this kit positions the valve continuously at any point between 0% and 100%. This is the required function for PID control loops for flow, temperature, and pressure.
Its IO-Link communication simultaneously transmits the modulating control signal, diagnostic data, and power through a single standard cable, radically simplifying wiring compared to conventional analog solutions. The integrated predictive diagnostics also detect actuator deterioration before it affects the process.
Modulating vs. ON-OFF — why proportional control is the correct specification for PID loops
The distinction between ON-OFF and modulating automation is the most important criterion when selecting the kit. The following cases describe when modulating is the correct specification:
- Continuous flow control — since ON-OFF only allows fully open or fully closed operation: When the process requires maintaining a specific flow rate that can vary between the minimum and maximum, the valve must be positioned at any point within the range. ON-OFF control cannot precisely regulate the flow rate. The modulating kit is, therefore, the only correct option for these processes.
- PID control loops where the valve acts as the final control element, since PID requires continuous regulation: The PID controller generates a continuous output signal proportional to the error between the actual and setpoint values. The modulating positioner receives that signal and precisely positions the valve.
It is also the standard component in advanced process control systems where control quality depends on the positioner's response.
- Processes with frequent demand variations — since the positioner continuously corrects the deviation: When process demand changes continuously, the positioner adjusts the valve position in real time. It also constantly compares the actual position with the desired position to immediately correct any deviation.
IO-Link — why a single cable outperforms conventional analog wiring even though both perform modulating control
IO-Link communication is the technological differentiator of this kit compared to standard analog positioners. Therefore, it significantly reduces installation and maintenance costs. Its advantages are described below:
- A single cable for signal, diagnostics, and power — since IO-Link is an all-in-one digital protocol: An analog positioner requires separate cables for the control signal, position feedback, and power. IO-Link transmits everything through a single standard cable. Consequently, it reduces the number of cables, PLC inputs/outputs, and field installation hours.
- Real-time predictive diagnostics — since the positioner transmits hours, temperature, cycles, and deviation to the PLC: The positioner continuously monitors the valve's operating parameters. When any value deviates from the normal range, it generates an alert event code in the PLC. The maintenance team can therefore detect deterioration before the valve fails, moving from reactive to predictive maintenance.
- No repeated self-calibration — since the positioner maintains accuracy autonomously: Conventional analog positioners require periodic recalibration to compensate for component drift. The IO-Link positioner in this kit does not require that process and maintains its accuracy throughout its useful life without periodic adjustment interventions.
- Compatible with PROFINET, EtherNet/IP, and EtherCAT — for integration with any PLC brand: The kit follows the international IO-Link standard and is compatible with IO-Link masters from major manufacturers. Therefore, it integrates with PLCs from any manufacturer without additional protocol converters.
Technical specifications defining the modulating automation kit for valves with IO-Link
| Parameter | Value |
|---|---|
| Automation type | Modulating — continuous proportional control from 0% to 100% |
| Communication technology | IO-Link — IEC 61131-9 standard digital protocol |
| Wiring | A single IO-Link cable (signal + diagnostics + power) |
| Compatible valves | Quarter-turn ball and butterfly valves |
| Transmitted data | Actual position, temperature, operating hours, diagnostics |
| Diagnostics | Real-time predictive — detailed event codes to the PLC |
| Self-calibration | Does not require repeated processes — autonomous |
| Compatible protocols | PROFINET — EtherNet/IP — EtherCAT |
IO-Link modulating kit vs. analog positioner — comparison table to select the correct one since they differ in wiring and diagnostics
| Criterion | 4-20 mA analog positioner | IO-Link modulating kit ← This product |
|---|---|---|
| Wiring | ⚠️ Separate cables for signal, feedback, and power | ✅ A single IO-Link cable — lower cost and installation time |
| Remote diagnostics | ❌ Not available — field inspection only | ✅ Continuous — position, temperature, hours, and alarms to the PLC in real time |
| Self-calibration | ⚠️ Periodic recalibration required — field intervention | ✅ Not required — maintains accuracy autonomously |
| Signal type | 4-20 mA analog — analog/digital conversion in the PLC | ✅ 100% digital — no analog signal noise or drift |
| Maintenance | ⚠️ Reactive — failure is detected after it has occurred | ✅ Predictive — deterioration is detected before failure |
| Network protocols | ⚠️ Analog signal only — no industrial network integration | ✅ PROFINET, EtherNet/IP, EtherCAT — native industrial network integration |
| Relative cost | ✅ Lower initial cost — for facilities without an industrial network | Higher initial investment — justified by lower maintenance costs and higher process availability |
Main applications of the modulating automation kit where IO-Link also provides predictive diagnostics
- Flow control in PID loops where the valve acts as the final control element: It is also the standard component in process plants where the flow must be maintained at a precise setpoint. The modulating positioner continuously adjusts the valve position, so the PID loop can operate precisely without limitations from the final element.
Compatibility with PROFINET, EtherNet/IP, and EtherCAT also allows it to be integrated into any existing control architecture.
- Temperature and pressure control where the valve regulates the heating fluid, coolant, or system pressure: In temperature control loops where the valve regulates the flow of heating or cooling fluid, the modulating positioner adjusts the position with the precision required by the PID controller. Predictive diagnostics also detect actuator deterioration before it affects control quality and generates deviations from the setpoint.
Applications in modernization, pharmaceuticals, and industrial networks where IO-Link also meets specific requirements
- Modernization of analog control loops where migration to IO-Link digital control is required without replacing the valve: In plants with conventional analog positioners, this kit allows migration to digital control without modifying the existing valve or actuator.
Simplified wiring also reduces the migration cost compared to replacing all loop instrumentation. Therefore, modernization is carried out gradually and without prolonged production downtime.
- Pharmaceutical and food industries where digital traceability of the positioner is a GMP validation requirement: In pharmaceutical and food processes, position, temperature, and operating hours data are recorded in the control system for auditing and validation.
Predictive diagnostics guarantee, since the positioner parameters are continuously monitored, that the instrument operates within the validated limits at all times.
- Plants with a PROFINET, EtherNet/IP, or EtherCAT network where direct positioner integration into the network is a requirement: In modern facilities with industrial network infrastructure, this kit integrates directly through its IO-Link master. It does not require additional converters.
Consequently, the positioner appears in the control system as just another device on the network, with all its diagnostic data accessible from the control room.
For the full range of automation kits, see automation kits collection →
