3-Way Control Valve | Mixing and Diverting | WCB and SS316 | -196°C to +450°C | ANSI 150/300/600

In stock
Regular price Solicitar precio
Extent

3-Way Control Valve for Mixing and Diverting — WCB or SS316, SS316 Trim, 3/4" to 14", with a temperature range of -196°C to +450°C

Cematic's 3-way control valve precisely regulates fluid flow in mixing or diverting systems. It is also the leading solution in processes where a single valve replaces the function of two. Unlike 2-way valves, which only regulate a single flow, the 3-way configuration allows two streams to be combined or one to be split between two outlets.

Its temperature range of -196°C to +450°C covers everything from cryogenic services to superheated steam, as the body and trim materials are selected based on the fluid and process temperature. The ±1% F.S. linearity with a positioner also ensures precise temperature or flow control in demanding PID loops.

The assembly includes a 3-way body, pneumatic diaphragm actuator, and positioner with a 4–20 mA signal. Cematic delivers it assembled and tested, so it is ready to install.

Mixing vs. diverting configuration — why the correct selection determines the assembly's function

The 3-way valve configuration determines the assembly's function in the process because the flow direction differs in each case:

  • Mixing configuration — two inlets, one outlet combining two streams: Two streams enter the valve and are mixed at the outlet in the proportion defined by the plug position. This is the standard configuration in hot and cold water mixing temperature control systems because the actuator regulates the mixing ratio to maintain the outlet temperature at the setpoint.
  • Diverting configuration — one inlet and two outlets for distributing flow: One stream enters the valve and is distributed between two outlets in the proportion controlled by the actuator. This is the correct configuration for recirculation and bypass systems, as it allows part of the flow to be diverted to a secondary circuit — cooling, recirculation, or backup — without interrupting the main flow.
  • "V" type plug — linear control characteristic for stable gain in the PID loop: The V-shaped plug creates a linear relationship between the stem position and the flow through each port. The ±1% F.S. linearity with a positioner also ensures that the PID control loop operates with stable gains across the entire opening range.

Body materials — options based on the fluid and process temperature

The body material is selected based on the fluid, temperature, and corrosion requirements, as this choice determines the assembly's service life and safety. The available options are described below, as the correct material selection is critical to the assembly's service life and safety:

  • A216 WCB — the first choice for general services and the lowest-cost option in the family: It is the most commonly specified material for steam, hot water, and natural gas services up to +425°C. It is also the lowest-cost option in the family, although it is not suitable for corrosive fluids or chlorides.
  • A216 WC6 — alloy steel for high temperatures, as it contains chromium and molybdenum: It is the option for steam services exceeding the WCB range. Its chromium and molybdenum content also provides greater resistance to oxidation and creep at elevated temperatures.
  • A352 LCB — carbon steel for cryogenic service, as it retains toughness at low temperatures: For low-temperature services down to -46°C, as LCB retains toughness at temperatures where WCB becomes brittle. Therefore, it is the correct choice for cryogenic services — liquefied gases and liquid nitrogen.
  • A351 CF8M — cast SS316 stainless steel, which resists chlorides and corrosive fluids: It is the option for corrosive fluids, chlorides, moderate acids, and seawater. The molybdenum in CF8M also inhibits pitting corrosion that would affect CF8 in these services.
  • A351 CF8, CF3M, CF3 — other stainless steel options also available depending on the fluid: These are options for fluids with specific corrosion or temperature requirements. The selection depends on the fluid and process conditions. Cematic's technical team can provide free guidance, as incorrect material specification can compromise safety.

Technical specifications defining the process limits for the 3-way control valve

Parameter Value
Configuration 3-way — mixing or diverting
Nominal diameters 3/4" to 14"
Body materials A216 WCB, WC6 | A352 LCB | A351 CF8, CF8M, CF3M, CF3
Trim (plug and seat) SS304 or SS316 stainless steel
Plug profile Type "V" — linear flow characteristic
Stem packing V-shaped PTFE or flexible PTFE + graphite
Nominal pressure ANSI Class 150, 300, or 600 LB
Connection ANSI B16.5 flange — FF, RF, RJ, or LG
Minimum temperature -196°C (cryogenic service with LCB)
Maximum temperature +450°C (with graphite packing)
Actuator Pneumatic diaphragm — single-acting
Actuator diaphragm EPDM-reinforced nylon
Spring range 80 to 240 kPa (0.8 to 2.4 kgf/cm²)
Air supply pressure 0.14 to 0.50 MPa
Air connection 1/4" NPT female thread
Actuator ambient temperature -30°C to +70°C
Positioner signal 4–20 mA
Hysteresis error with positioner Within 1% F.S.
Linearity with positioner ±1% F.S.

3-way control valve vs. 2-way — comparison table for selecting the correct configuration for the process

Criterion 2-way control valve 3-way control valve ← This product
Main function Regulates flow in a single line only ✅ Mixes or diverts between two lines — a function the 2-way valve cannot perform
Mixing temperature control ❌ Not possible without two valves and an additional loop ✅ A single valve mixes two streams to control the outlet temperature
Automatic bypass and recirculation ❌ Requires a configuration of two separate valves ✅ A single valve distributes flow between the main line and the bypass
Number of valves in the system ⚠️ Two valves, plus greater installation complexity ✅ A single valve — lower installation cost and less pressure drop than the 2-way version
Control loop complexity ⚠️ Greater complexity, as it requires two control signals ✅ Lower complexity — a single 4–20 mA signal controls the mixing or diverting ratio
System pressure drop ✅ Lower, as there is only one restriction in the line Higher pressure drop — its only disadvantage compared to the 2-way valve

Fluid compatibility — how to select the body material, as it determines chemical resistance

  • ✅ Saturated and superheated steam up to 450°C — compatible — WCB or WC6 withstands high-temperature conditions
  • ✅ Hot water, boiler feedwater, and condensate up to 450°C — compatible with a WCB body and graphite packing
  • ✅ Natural gas, LPG, and dry industrial gases — compatible — the WCB or CF8M body selection depends on the H₂S concentration
  • ✅ Refining and petrochemical process fluids — compatible; CF8M is specified when the fluid contains chlorides
  • ✅ Cryogenic fluids down to -196°C — compatible with an LCB body — LCB retains toughness at low temperatures
  • ✅ Corrosive fluids and water with chlorides — with a CF8M body (cast SS316), as molybdenum inhibits pitting corrosion
  • ✅ Process water, aqueous fluids, and industrial solutions — compatible; CF8M is preferred when the water contains chlorides
  • ⚠️ High H₂S concentrations — specify NACE MR0175 materials, as SSC can degrade standard steels
  • ⚠️ Fluids with suspended solids — check for a suitable plug profile; install an upstream filter
  • ❌ Concentrated acids (HCl, H₂SO₄ >30%), HF — incompatible — use special-material bodies and trim; consult Cematic

Main applications where the 3-way control valve is the correct specification

  • Industrial HVAC where hot and cold water mixing controls the temperature: The mixing valve regulates the hot and cold water ratio to maintain the supply temperature at the control loop setpoint. It is the standard solution in HVAC systems for large industrial and hospital facilities. A single valve replaces the function of two, simplifying the control loop.
  • Chemical and petrochemical processes requiring precise stream mixing: Mixes or diverts fluids between process lines with ±1% F.S. linearity, ensuring control loop precision. The V-shaped plug provides a linear flow characteristic, and the loop gain remains stable across the entire opening range.
  • Heat exchangers where the process temperature depends on the mixing ratio: Regulates the temperature of the fluid entering the exchanger by mixing the hot stream and the bypass stream. The positioner's precise control also maintains the process temperature within the design ranges even when inlet conditions vary.
  • Hydraulic and pneumatic systems requiring automatic switching between circuits: Distributes flow between the main line and the backup circuit based on process demand. This improves operational flexibility and facilitates redundancy in critical facilities without the need for two separate valves.
  • Steam generation and distribution where thermal control is critical: Diverts or mixes steam and condensate to control temperature in power plants. The temperature range up to +450°C also covers superheated steam services where other valves with lower specifications are not viable.

For the complete category of control valves, see Cematic Control Valves →

Data Sheet